FAQS
What is the drain on the WiseDim when it is turned off?
When switched off, the power drain for the WiseDim is 20mA.
How many switches can I add to the Wise Receivers?
You can add a maximum of 32 mixed switches to each Wise receiver, for example, 4 PIR sensors, 20 wall switches and 8 remotes.
How many Wise Receivers can I control from one swtich or remote?
You can operate as many as you like, there is no limit (you must be in range for the receivers to work). You will however be switching a circuit from each receiver on at the same time.
What is the signal range of the Wise Receivers?
Outside, the range is approximately 250 metres in open areas, inside the range is shorter, this depends on how many objects the signal has to go through. For example if you fitted the WiseDim in your brick garage and that was 30 metres away from your house and the switch was located behind two brick walls, then the range might be reduce to 50 metres.
Can changes be made to the casing of the Wise Receivers?
No. Any changes to any of these products will void the warranty.
Are the products online compatible with the original switchable WiseBox?
No. All products online use the 868MHz frequency. The original WiseBox uses the 433MHz frequency. The original Wise Box comes with a black key fob and oval buttons on the wall switch.
Can you fit the Wise Receivers outside?
The WiseDim and WiseBox are rated at IP54, so you can fit the box almost anywhere, inside or out. It cannot be submerged. The other receivers cannot be fitted outside without putting the receiver into a waterproof box.
How many different switches, ie Wall Switch, Remote, PIR can I add to the Wise Receivers?
The maximum amount mixed switches is 32 total. i.e. 5 wall switches, 25 remotes, and 2 PIR sensors.
How long is the warranty on the Wise Controls products?
The warranty is 1 year, this covers manufacturing defects.
Is there a signal booster for the Wise Controls products?
Yes. There is a plug-in booster. This booster will amplify and repeat the signal giving 150 metres range from the booster. You can use more than one booster.
Technical Information
PROGRAMMING
To programming the WiseDim Box follow these steps.
How to install the WiseDim?
Connect a mains 240V supply into the WiseDim box using terminals 9(Live),10(Neutral) and 11(Earth).
Connect up to four circuits using terminals 16-23(Live and Neutral, 240V output).
How to change the switching mode?
The dip switch panel at the top right within the WiseDim can change the switching mode from switching to dimming.
Caution - Make sure that the circuit is OFF before changing the dip switch and the circuit can be dimmed.
The dip switch in the UP position will change the channel to a dimming circuit.
The dip switch in the DOWN position will change the channel to an on/off switching circuit (default position).
When in dimming mode, hold the button on the switch to dim the circuit.
How to program the WiseDim circuits?
Make sure that the mains 240V supply into the WiseDim box is ON.
Press and hold 'P1' (Circuit one), the buzzer will sound continuously.
With 'P1' held down, press one of the main four buttons on the wall or remote switch.
The buzzer will sound intermittently to confirm the programming is successful.
You will now be able to control channel 1 using the selected switch button.
Repeat this procedure for all circuits that you have connected to the WiseDim Box. Do this using P2, P3 and P4, and the remaining buttons on the switch.
How to program the WiseDim with the 7 button style switch (ALL ON / 2 ON / ALL OFF) functions?
The 'P5' button programs all circuits to switch on/off. To program this feature you will need to have a 7 button switch (uses the three bottom buttons on the switch).
Press and hold 'P5' (All Circuits), the buzzer will sound continuously.
With 'P5' held down, press any one of the three buttons at the bottom of the 7 button wall switch.
The buzzer will sound intermittently to confirm the programming is successful.
The function is now activated and works as follows, the left button turns on all circuits, the middle button turns on the first 2 circuits (and the right button turns off all circuits).
How to program the WiseDim ON/OFF function?
The 'P5' button programs all circuits to switch on/off. To program this feature you will need to have a 2 or 4 button switch (uses two of the buttons on the switch)
Press and hold 'P5' (All Circuits), the buzzer will sound continuously.
With 'P5' held down, press any one of the two buttons that will be used.
The buzzer will sound intermittently to confirm the programming is successful.
The function is now activated and works as follows, button 1 will be on & button 2 will be off, button 3 will be on & button 4 will be off. On a four button switch this function can be used to control 2 WiseDim boxes.
How to delete a channels memory?
Press the P5 button once, let go and then press again and hold, then press the switch button that you would like to delete.
To delete all channels press button 5 three times and hold when pressed the third time for 10 seconds.
FUSES
How to change the internal fuse?
The WiseDim is fused, they protect all the individual dimming circuits. Take the lid off the fuse holder. Remove the fuse from the holder and replace with a 240V 5A quick blow fuse.
AERIAL
How to install a different aerial?
Remove the single cable aerial from the terminal. Wire the new aerial to the same terminal.
If you are using co-axial cable the centre cable is connected to the same terminal as the standard aerial. The outer sleeving is connected to the the next terminal.
 | Technical Information |
 | FAQS |